Crestron C2N-SDC Guida di Installazione Scaricare il pdf

As of the date of manufacture, the C2N-SDC has been tested and found to comply with

specifications for CE marking.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Crestron Electronics, Inc. Operations & Installation Guide - DOC. 6316A

15 Volvo Drive Rockleigh, NJ 07647 (2011633)

Tel: 888.CRESTRON 11.14

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

Further Inquiries

To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at

1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of

Crestron worldwide offices at www.crestron.com/offices.

To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.

First-time users must establish a user account to fully benefit from all available features.

Future Updates

As Crestron improves functions, adds new features, and extends the capabilities of the C2N-SDC, additional

information may be made available as manual updates. These updates are solely electronic and serve as

intermediary supplements prior to the release of a complete technical documentation revision.

Check the Crestron website periodically for manual update availability and its relevance. Updates are identified as

an “Addendum” in the Download column.

WARNING: To avoid fire, shock, or death, turn off power at circuit breaker or fuse and test that power is off before

wiring!

NOTES: Observe the following points.

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• This product should be installed by a qualified electrician.

PREPARING AND CONNECTING WIRES

Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking the conductors. Twist together

the ends of the wires that share a connection. Apply solder only to the ends of the twisted wires. Avoid tinning too

far up the wires or the end becomes brittle.

Crestron C2N-SDC

Shade and Drape Controller, 120 Vac

Operations & Installation Guide

DESCRIPTION

The Crestron

C2N-SDC is a 2-channel shade and drape controller designed to provide a

convenient and cost-effective solution for controlling a variety of motorized window

treatments as well as motorized doors, sunroofs, lifts, and projection screens. The

C2N-SDC is a Cresnet

device with two independently controlled 120 Vac outputs. Each

output provides up and down or open and close control of a conventional three-wire

bidirectional motor. Built-in timing and interlock logic make it easy to program the C2N-SDC

for failsafe operation.

INSTALLATION

NOTE: Before using the C2N-SDC, ensure the device is using the latest firmware. Check

for the latest firmware for the C2N-SDC at www.crestron.com/firmware. Firmware is

loaded onto the device using Crestron Toolbox™.

The C2N-SDC can be mounted in a 2-gang electrical box or a 4 inch square (1900)

electrical box. The electrical box must be at least 1 1/2 inches (39 mm).

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

● Do not use outdoors.

● Do not mount near gas or electric heaters.

● Equipment should be mounted in locations and at heights where it will not be

subjected to tampering by unauthorized personnel.

● The use of accessory equipment not recommended by the manufacturer may cause

an unsafe condition.

● Do not use this equipment for other than its intended use.

● All servicing should be performed by qualified service personnel.

● If any Emergency Circuits are fed or controlled from this panel, it must be located

electrically where fed from a UPS, generator, or other guaranteed source of power

during emergency and power outage situations.

SAVE THESE INSTRUCTIONS.

Mounting to a 2-Gang Box

When mounting in a 2-gang electrical box, use the four #06-32 3/8 inch pan head screws,

two #6 washers, and two 1/4 inch ID nylon cable clamps. Mount the 2-gang electrical box

horizontally (with the mounting tabs on the left and right sides of the box) to maintain an

upright orientation of the C2N-SDC. Refer to the following illustration (wiring is not shown

for clarity).

Mounting to a 4 Inch Square (1900) Box

When mounting the C2N-SDC in a 4 inch square electrical box, use the two 8-32 3/8 inch

pan head screws, two #8 flat washers, and the two 1/4 inch ID nylon cable clamps as

shown in the following illustration (wiring is not shown for clarity).

(2) 1/4 in ID Nylon Cable Clamps

(2) 8-32 3/8 in Pan Head

Screws

(2) #8 Flat Washers

4 in Square (1900) Electrical Box

2-Gang Electrical Box

(4) 06-32 3/8 in

Pan Head Screws

(2) #6 Flat

Washers

(2) 1/4 in ID Nylon

Cable Clamps

1 2

Sommario

Pagina 1 - Crestron C2N-SDC

As of the date of manufacture, the C2N-SDC has been tested and found to comply with specifications for CE marking.FCC Compliance StatementThis device

Pagina 2 - OPERATION

Product warranty can be found at www.crestron.com/warranty.The specific patents that cover Crestron products are listed at patents.crestron.com.Crestr

Commenti su questo manuale

Nessun commento

Crestron C2N-SDC Guida di Installazione

Navigare online o scaricare Guida di Installazione per no Crestron C2N-SDC. Crestron C2N-SDC Installation guide Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi no Crestron C2N-SDC